Gabelstapler, Dieselstapler

STILL RX70-35 - NUR 1076 h - Triplex 4590 mm

Zustand: einsatzbereit (gebraucht), Baujahr: 1988, Funktionsfähigkeit: voll funktionsfähig, Maschinen-/Fahrzeugnummer: 65951607, Farbkanäle: 4, Papiergewicht (min.): 60 g/m², Papiergewicht (max.): 500 g/m², Papierbreite (max.): 720 mm, Papierhöhe (max.): 520 mm, Eingangsspannung: 400 V, Koenig Bauer / KBA Rapida SRO 4 | 1988 | Offsetdruckmaschine Baujahr: 1988 Format: 52x72 cm Farben – 4-Farben-Offset Geschwindigkeit – 12.000 Bogen/Stunde Papiergewicht – 60–500 g/m² Anleger – Mabeg (± Technotrans) Farbwerkverstellung – Colortronic Fernbedienung Feuchtwerk – Technotrans / Varidamp (Alkohol) Trockner – Infrarot Puderstreuer – Weko Kühlung – Baldwin Chromzylinder Dusdpfxjwzt Tts Acusp

Baujahr: 2022, Zustand: gebraucht, Technical data: Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Compressed air: 5–40°C Noise level: 82 dB(A) Color: Grey RAL 7035 Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. Dsdpfx Acjxx Tbcsueup • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Zustand: gut (gebraucht), Baujahr: 2003, Funktionsfähigkeit: voll funktionsfähig, Maschinen-/Fahrzeugnummer: 7555605, Maximalformat: 60 x 41 cm, integrierter Anleger SE - 18.2, Querschneider ST - 18.2, Stanzstation D - 18, Umreifungs-/Bandeinheit PB - 18.1, horizontale und vertikale Umreifung. Papierbreite min. 35 x 45 mm, Papierbreite max. 405 x 600 mm. Stapelhöhe min. 30 mm, Stapelhöhe max. 100 mm. Maschinen-Nr.: 7555605 Djdpfx Acexc Uv Aoueup

Zustand: einsatzbereit (gebraucht), Funktionsfähigkeit: voll funktionsfähig, PMC MODELL 200 Stanzmaschine. Duedpfjw I Sifex Acusp Maximale Etikettengröße: 178 x 203 mm Minimale Etikettengröße: 25 x 50 mm Beschnittzugabe: 3 mm Stapelhöhe: 102 mm Etiketten pro Stunde: bis zu 1.200.000 Elektrischer Anschluss: 3,5 kVA Versandgewicht: 700 kg Preis auf Anfrage